• Advertisement

Cisco SA540 - Classical Routing Problem - 0.0.0.0 in static Route

Linksys, Netgear, sonicwall, ect. Webbase configurations for firewalls. Web filting traffic shaping.

Cisco SA540 - Classical Routing Problem - 0.0.0.0 in static Route

Postby Guest » Wed Oct 13, 2010 12:03 am

Hello, Im a little newbie with Routing Device,

 


I had several Public IP

 

I had a Cisco Pix 501and want to replace it by a Cisco SA540

 


my Wan IP on Pix 501 is 195.68.x.z
my Lan IP on Pix 501 is 62.23.a.b and 62.23.a.c ,...

 


My Pix 501 Translation rules is : inside interface|inside:any:0.0.0.0|outside interface| same as orginal address
My Pix 501 Static route : outside |Ip address 0.0.0.0|Netmask 0.0.0.0|Gateway IP 195.168.x.y|Metric 1

 


So when a computer with 62.23.a.X want to acces to internet the static route tell it to throuw the Gateway IP 195.168.x.y (as I undestand)

 

I have to replicate this config to my SA540

 

So via the Web GUI, I configure the Wan and Lan IP
, then in routing menu I check "Classical Routing" then I go to Static Menu in order to add the same route as in my Pix 501, but I can put 0.0.0.0 in iP address nor in IP Subnet Mask.

 

Can anyone help me ?

 

Thanks a lot.

Guest
 

Advertisement

Re:Cisco SA540 - Classical Routing Problem - 0.0.0.0 in static Route

Postby Guest » Wed Oct 13, 2010 12:29 am

The PIX and SA500 work differently and are configured differently.  Often, you don configure a PIX and IOS in the same fashion because they use a different configuration.

 

From what I have read that you are trying to do.  The SA540 has a default route to go out through the WAN port.  If you look at the routing table under the diagnostics page, I think you will see a route with 0.0.0.0 and subnet of 0.0.0.0 going to the default GW of your router.

Guest
 

Re:Cisco SA540 - Classical Routing Problem - 0.0.0.0 in static Route

Postby Guest » Wed Oct 13, 2010 12:33 am

Thanks Steven for you answer.

So you mean , for what I want, I don"t have to put a static route ? because when I check "Classical Routing" I don have access to the Internet.

I think I forgot something.

Guest
 

Re:Cisco SA540 - Classical Routing Problem - 0.0.0.0 in static Route

Postby Guest » Wed Oct 13, 2010 1:26 am

Whatever I set : NAT or CLASSICAL ROUTE my Router Options in Diagnostic menu is :

 

Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
127.0.0.1       localhost       255.255.255.255 UGH   1      0        0 lo
92.103.214.164  *               255.255.255.252 U     0      0        0 eth1
92.103.213.168  *               255.255.255.248 U     0      0        0 bdg1
92.103.213.168  roubaix         255.255.255.248 UG    1      0        0 bdg1
default         92.103.214.165  0.0.0.0         UG    0      0        0 eth1

 

when I select NAT I can access to the internet, when I select CLASSICAL ROUTE I don have any access.

Guest
 

Re:Cisco SA540 - Classical Routing Problem - 0.0.0.0 in static Route

Postby Guest » Wed Oct 13, 2010 1:37 am

routage_internet_cisco_540.jpg

Guest
 



  • Advertisement


Similar topics


Return to Small Business Security

Who is online

Users browsing this forum: No registered users and 1 guest